Finde den Fehler nicht

18 Nov 2003

      Hi,

bin immer noch dabei, die zweite Grafikkarte und den zweiten Monitor 
einzubinden und finde den Fehler nicht. System ist Knoppix 3.3 mit 
Kernel 2.4.22 auf Festplatte.

lspci | grep VGA gibt folgendes aus:

#schnipp

00:0d.0 VGA compatible controller: Matrox Graphics, Inc. MGA 2064W 
[Millennium] (rev 01)
01:00.0 VGA compatible controller: nVidia Corporation NV20 [GeForce3 Ti 
200] (rev a3)

#schnapp

cat /proc/pci sagt folgendes:

#schnipp

PCI devices found:
   Bus  0, device   0, function  0:
     Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333] 
(rev 0).
       Prefetchable 32 bit memory at 0xfc000000 [0xfdffffff].
   Bus  0, device   1, function  0:
     PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 
AGP] (rev 0).
       Master Capable.  No bursts.  Min Gnt=8.
   Bus  0, device   5, function  0:
     Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 16).
       IRQ 10.
       Master Capable.  Latency=32.  Min Gnt=2.Max Lat=24.
       I/O at 0xd800 [0xd8ff].
   Bus  0, device  13, function  0:
     VGA compatible controller: Matrox Graphics, Inc. MGA 2064W 
[Millennium] (rev 1).
       IRQ 11.
       Non-prefetchable 32 bit memory at 0xeb800000 [0xeb803fff].
       Prefetchable 32 bit memory at 0xee800000 [0xeeffffff].
   Bus  0, device  15, function  0:
     Multimedia video controller: Brooktree Corporation Bt878 Video 
Capture (rev 2).
       IRQ 5.
       Master Capable.  Latency=32.  Min Gnt=16.Max Lat=40.
       Prefetchable 32 bit memory at 0xed800000 [0xed800fff].
   Bus  0, device  15, function  1:
     Multimedia controller: Brooktree Corporation Bt878 Audio Capture 
(rev 2).
       IRQ 5.
       Master Capable.  Latency=32.  Min Gnt=4.Max Lat=255.
       Prefetchable 32 bit memory at 0xed000000 [0xed000fff].
   Bus  0, device  16, function  0:
     Ethernet controller: Realtek Semiconductor Co., Ltd. 
RTL-8139/8139C/8139C+ (rev 16).
       IRQ 9.
       Master Capable.  Latency=32.  Min Gnt=32.Max Lat=64.
       I/O at 0xd400 [0xd4ff].
       Non-prefetchable 32 bit memory at 0xeb000000 [0xeb0000ff].
   Bus  0, device  17, function  0:
     ISA bridge: VIA Technologies, Inc. VT8233A ISA Bridge (rev 0).
   Bus  0, device  17, function  1:
     IDE interface: VIA Technologies, Inc. 
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 6).
       IRQ 11.
       Master Capable.  Latency=32.
       I/O at 0xd000 [0xd00f].
   Bus  0, device  17, function  2:
     USB Controller: VIA Technologies, Inc. USB (rev 35).
       IRQ 9.
       Master Capable.  Latency=32.
       I/O at 0xb800 [0xb81f].
   Bus  0, device  17, function  3:
     USB Controller: VIA Technologies, Inc. USB (#2) (rev 35).
       IRQ 9.
       Master Capable.  Latency=32.
       I/O at 0xb400 [0xb41f].
   Bus  1, device   0, function  0:
     VGA compatible controller: nVidia Corporation NV20 [GeForce3 Ti 
200] (rev 163).
       IRQ 11.
       Master Capable.  Latency=64.  Min Gnt=5.Max Lat=1.
       Non-prefetchable 32 bit memory at 0xec000000 [0xecffffff].
       Prefetchable 32 bit memory at 0xf0000000 [0xf7ffffff].
       Prefetchable 32 bit memory at 0xef800000 [0xef87ffff].

#schnapp

Die Karte, auf die beim booten zuerst zugegriffen wird, ist die Geforce.
Ich bin folgendermaßen vorgegangen:
Habe die Geforce ausgebaut und den Rechner mit einer Knoppix-CD und der 
Matroxkarte gebootet. Hab die XF86-Config-4 auf Diskette kopiert. 
Rechner runtergefahren, die Geforce wieder eingebaut und von Festplatte 
gebootet. Anschließend habe ich die XF86Config wie nachfolgend editiert 
und in nach /etc/X11 kopiert:

#schnipp

Section "ServerLayout"
	Identifier     "XFree86 Configured"
	Screen      0  "Screen1" 0 0
	Screen      1  "Screen0" RightOf "Screen1"
	InputDevice    "Keyboard0" "CoreKeyboard"
	InputDevice    "PS/2 Mouse" "CorePointer"
# Serial Mouse not detected
# USB Mouse not detected
EndSection

Section "ServerFlags"
	Option "AllowMouseOpenFail"  "true"

EndSection

Section "Files"
	RgbPath      "/usr/X11R6/lib/X11/rgb"
	ModulePath   "/usr/X11R6/lib/modules"
	FontPath     "/usr/X11R6/lib/X11/fonts/misc:unscaled"
	FontPath     "/usr/X11R6/lib/X11/fonts/misc"
	FontPath     "/usr/X11R6/lib/X11/fonts/75dpi:unscaled"
	FontPath     "/usr/X11R6/lib/X11/fonts/75dpi"
	FontPath     "/usr/X11R6/lib/X11/fonts/100dpi:unscaled"
	FontPath     "/usr/X11R6/lib/X11/fonts/100dpi"
	FontPath     "/usr/X11R6/lib/X11/fonts/Speedo"
	FontPath     "/usr/X11R6/lib/X11/fonts/PEX"
# Additional fonts: Locale, Gimp, TTF...
	FontPath     "/usr/X11R6/lib/X11/fonts/cyrillic"
#	FontPath     "/usr/X11R6/lib/X11/fonts/latin2/75dpi"
#	FontPath     "/usr/X11R6/lib/X11/fonts/latin2/100dpi"
# True type and type1 fonts are also handled via xftlib, see 
/etc/X11/XftConfig!
	FontPath     "/usr/X11R6/lib/X11/fonts/Type1"
	FontPath     "/usr/share/fonts/ttf/western"
	FontPath     "/usr/share/fonts/ttf/decoratives"
	FontPath     "/usr/share/fonts/truetype"
	FontPath     "/usr/share/fonts/truetype/openoffice"
	FontPath     "/usr/share/fonts/truetype/ttf-bitstream-vera"
	FontPath     "/usr/share/fonts/latex-ttf-fonts"
	FontPath     "/usr/X11R6/lib/X11/fonts/defoma/CID"
	FontPath     "/usr/X11R6/lib/X11/fonts/defoma/TrueType"
EndSection

Section "Module"
         Load  "ddc"  # ddc probing of monitor
	Load  "GLcore"
	Load  "dbe"
	Load  "dri"
	Load  "extmod"
	Load  "glx"
         Load  "bitmap" # bitmap-fonts
	Load  "speedo"
	Load  "type1"
	Load  "freetype"
	Load  "record"
EndSection

Section "InputDevice"
	Identifier  "Keyboard0"
	Driver      "keyboard"
         Option      "CoreKeyboard"
	Option "XkbRules" "xfree86"
	Option "XkbModel" "pc105"
	Option "XkbLayout" "de"
	Option "XkbVariant" "nodeadkeys"
EndSection

Section "InputDevice"
	Identifier  "Serial Mouse"
	Driver      "mouse"
	Option      "Protocol" "Microsoft"
	Option      "Device" "/dev/ttyS0"
	Option      "Emulate3Buttons" "true"
	Option      "Emulate3Timeout" "70"
	Option	    "SendCoreEvents"  "true"
EndSection

Section "InputDevice"
	Identifier  "PS/2 Mouse"
	Driver      "mouse"
	Option      "Protocol" "auto"
Option          "ZAxisMapping"          "4 5"
	Option      "Device" "/dev/psaux"
	Option      "Emulate3Buttons" "true"
	Option      "Emulate3Timeout" "70"
	Option	    "SendCoreEvents"  "true"
EndSection

Section "InputDevice"
         Identifier      "USB Mouse"
         Driver          "mouse"
         Option          "Device"                "/dev/input/mice"
	Option		"SendCoreEvents"	"true"
         Option          "Protocol"              "IMPS/2"
         Option          "ZAxisMapping"          "4 5"
         Option          "Buttons"               "5"
EndSection

# Auto-generated by KNOPPIX mkxf86config

Section "Monitor"
	Identifier	"Monitor0"
	Option	"DPMS"	"true"
#	HorizSync    28.0 - 78.0 # Warning: This may fry very old Monitors
	HorizSync    28.0 - 96.0 # Warning: This may fry old Monitors
#	VertRefresh  50.0 - 76.0 # Very conservative. May flicker.
	VertRefresh  50.0 - 62.0 # Extreme conservative. Will flicker. TFT default.
	# These are the DDC-probed settings reported by your monitor.
	# 1280x1024, 75.0Hz; hfreq=79.98, vfreq=75.03
	ModeLine "1280x1024"	135.00 1280 1296 1440 1688 1024 1025 1028 1066 
+hsync +vsync
	# 1024x768, 75.0Hz; hfreq=60.02, vfreq=75.03
	ModeLine "1024x768"	 78.75 1024 1040 1136 1312  768  769  772  800 
+hsync +vsync
	# 1024x768, 70.0Hz; hfreq=56.48, vfreq=70.07
	ModeLine "1024x768"	 75.00 1024 1048 1184 1328  768  771  777  806 
-hsync -vsync
	# 1024x768, 60.0Hz; hfreq=48.36, vfreq=60.00
	ModeLine "1024x768"	 65.00 1024 1048 1184 1344  768  771  777  806 
-hsync -vsync
	# 800x600, 75.0Hz; hfreq=46.88, vfreq=75.00
	ModeLine "800x600"	 49.50  800  816  896 1056  600  601  604  625 
+hsync +vsync
	# 800x600, 72.0Hz; hfreq=48.08, vfreq=72.19
	ModeLine "800x600"	 50.00  800  856  976 1040  600  637  643  666 
+hsync +vsync
	# 800x600, 60.0Hz; hfreq=37.88, vfreq=60.32
	ModeLine "800x600"	 40.00  800  840  968 1056  600  601  605  628 
+hsync +vsync
	# 800x600, 56.0Hz; hfreq=35.16, vfreq=56.25
	ModeLine "800x600"	 36.00  800  824  896 1024  600  601  603  625 
+hsync +vsync
	# 640x480, 75.0Hz; hfreq=37.50, vfreq=75.00
	ModeLine "640x480"	 31.50  640  656  720  840  480  481  484  500 
-hsync -vsync
	# 640x480, 72.0Hz; hfreq=37.86, vfreq=72.81
	ModeLine "640x480"	 31.50  640  656  696  816  480  481  484  504 
-hsync -vsync
	# 640x480, 60.0Hz; hfreq=31.47, vfreq=59.94
	ModeLine "640x480"	 25.17  640  648  744  784  480  482  484  509 
-hsync -vsync
	# Extended modelines with GTF timings
	# 640x480 @ 100.00 Hz (GTF) hsync: 50.90 kHz; pclk: 43.16 MHz
	ModeLine "640x480"  43.16  640 680 744 848  480 481 484 509  -HSync +Vsync
	# 768x576 @ 60.00 Hz (GTF) hsync: 35.82 kHz; pclk: 34.96 MHz
	ModeLine "768x576"  34.96  768 792 872 976  576 577 580 597  -HSync +Vsync
	# 768x576 @ 72.00 Hz (GTF) hsync: 43.27 kHz; pclk: 42.93 MHz
	ModeLine "768x576"  42.93  768 800 880 992  576 577 580 601  -HSync +Vsync
	# 768x576 @ 75.00 Hz (GTF) hsync: 45.15 kHz; pclk: 45.51 MHz
	ModeLine "768x576"  45.51  768 808 888 1008  576 577 580 602  -HSync +Vsync
	# 768x576 @ 85.00 Hz (GTF) hsync: 51.42 kHz; pclk: 51.84 MHz
	ModeLine "768x576"  51.84  768 808 888 1008  576 577 580 605  -HSync +Vsync
	# 768x576 @ 100.00 Hz (GTF) hsync: 61.10 kHz; pclk: 62.57 MHz
	ModeLine "768x576"  62.57  768 816 896 1024  576 577 580 611  -HSync +Vsync
	# 800x600 @ 100.00 Hz (GTF) hsync: 63.60 kHz; pclk: 68.18 MHz
	ModeLine "800x600"  68.18  800 848 936 1072  600 601 604 636  -HSync +Vsync
	# 1024x768 @ 100.00 Hz (GTF) hsync: 81.40 kHz; pclk: 113.31 MHz
	ModeLine "1024x768"  113.31  1024 1096 1208 1392  768 769 772 814 
-HSync +Vsync
	# 1152x864 @ 60.00 Hz (GTF) hsync: 53.70 kHz; pclk: 81.62 MHz
	ModeLine "1152x864"  81.62  1152 1216 1336 1520  864 865 868 895 
-HSync +Vsync
	# 1152x864 @ 85.00 Hz (GTF) hsync: 77.10 kHz; pclk: 119.65 MHz
	ModeLine "1152x864"  119.65  1152 1224 1352 1552  864 865 868 907 
-HSync +Vsync
	# 1152x864 @ 100.00 Hz (GTF) hsync: 91.50 kHz; pclk: 143.47 MHz
	ModeLine "1152x864"  143.47  1152 1232 1360 1568  864 865 868 915 
-HSync +Vsync
	# 1280x960 @ 72.00 Hz (GTF) hsync: 72.07 kHz; pclk: 124.54 MHz
	ModeLine "1280x960"  124.54  1280 1368 1504 1728  960 961 964 1001 
-HSync +Vsync
	# 1280x960 @ 75.00 Hz (GTF) hsync: 75.15 kHz; pclk: 129.86 MHz
	ModeLine "1280x960"  129.86  1280 1368 1504 1728  960 961 964 1002 
-HSync +Vsync
	# 1280x960 @ 100.00 Hz (GTF) hsync: 101.70 kHz; pclk: 178.99 MHz
	ModeLine "1280x960"  178.99  1280 1376 1520 1760  960 961 964 1017 
-HSync +Vsync
	# 1280x1024 @ 100.00 Hz (GTF) hsync: 108.50 kHz; pclk: 190.96 MHz
	ModeLine "1280x1024"  190.96  1280 1376 1520 1760  1024 1025 1028 1085 
  -HSync +Vsync
	# 1400x1050 @ 60.00 Hz (GTF) hsync: 65.22 kHz; pclk: 122.61 MHz
	ModeLine "1400x1050"  122.61  1400 1488 1640 1880  1050 1051 1054 1087 
  -HSync +Vsync
	# 1400x1050 @ 72.00 Hz (GTF) hsync: 78.77 kHz; pclk: 149.34 MHz
	ModeLine "1400x1050"  149.34  1400 1496 1648 1896  1050 1051 1054 1094 
  -HSync +Vsync
	# 1400x1050 @ 75.00 Hz (GTF) hsync: 82.20 kHz; pclk: 155.85 MHz
	ModeLine "1400x1050"  155.85  1400 1496 1648 1896  1050 1051 1054 1096 
  -HSync +Vsync
	# 1400x1050 @ 85.00 Hz (GTF) hsync: 93.76 kHz; pclk: 179.26 MHz
	ModeLine "1400x1050"  179.26  1400 1504 1656 1912  1050 1051 1054 1103 
  -HSync +Vsync
	# 1400x1050 @ 100.00 Hz (GTF) hsync: 111.20 kHz; pclk: 214.39 MHz
	ModeLine "1400x1050"  214.39  1400 1512 1664 1928  1050 1051 1054 1112 
  -HSync +Vsync
	# 1600x1200 @ 100.00 Hz (GTF) hsync: 127.10 kHz; pclk: 280.64 MHz
	ModeLine "1600x1200"  280.64  1600 1728 1904 2208  1200 1201 1204 1271 
  -HSync +Vsync
EndSection

Section "Monitor"
	Identifier	"Monitor1"
	Option	"DPMS"	"true"
#	HorizSync    28.0 - 78.0 # Warning: This may fry very old Monitors
	HorizSync    28.0 - 96.0 # Warning: This may fry old Monitors
	VertRefresh  50.0 - 76.0 # Very conservative. May flicker.
# These are some Modelines that happen to work on many systems
# Especially the "1024x768" has been thoroughly tested, even on Laptops
	Modeline "640x480"     25.175 640  664  760  800   480  491  493  525 #60Hz
	Modeline "800x600"     40.12  800  848  968 1056   600  601  605  628 #60Hz
	Modeline "1024x768"    85    1024 1056 1152 1360   768  784  787  823
	Modeline "1152x864"    92    1152 1208 1368 1474   864  865  875  895
	Modeline "1152x864"   110    1152 1240 1324 1552   864  864  876  908
	Modeline "1152x864"   135    1152 1464 1592 1776   864  864  876  908
	Modeline "1152x864"   137.65 1152 1184 1312 1536   864  866  885  902 
-HSync -VSync
	Modeline "1280x1024"   80    1280 1296 1512 1568  1024 1025 1037 1165 
Interlace
	Modeline "1280x1024"  110    1280 1328 1512 1712  1024 1025 1028 1054
	Modeline "1280x1024"  126.5  1280 1312 1472 1696  1024 1032 1040 1068 
-HSync -VSync
	Modeline "1280x1024"  135    1280 1312 1456 1712  1024 1027 1030 1064
	Modeline "1280x1024"  135    1280 1312 1416 1664  1024 1027 1030 1064
	Modeline "1280x1024"  157.5  1280 1344 1504 1728  1024 1025 1028 1072 
+HSync +VSync
	Modeline "1280x1024"  181.75 1280 1312 1440 1696  1024 1031 1046 1072 
-HSync -VSync
	Modeline "1600x1200"  162    1600 1664 1856 2160  1200 1201 1204 1250 
+HSync +VSync
	Modeline "1600x1200"  189    1600 1664 1856 2160  1200 1201 1204 1250 
-HSync -VSync
	Modeline "1600x1200"  202.5  1600 1664 1856 2160  1200 1201 1204 1250 
+HSync +VSync
	Modeline "1600x1200"  220    1600 1616 1808 2080  1200 1204 1207 1244 
+HSync +VSync
	ModeLine "1800x1440"  230    1800 1896 2088 2392  1440 1441 1444 1490 
+HSync +VSync
	ModeLine "1800x1440"  250    1800 1896 2088 2392  1440 1441 1444 1490 
+HSync +VSync
EndSection

Section "Device"
	### Available Driver options are:-
# sw_cursor is needed for some ati and radeon cards
Option "sw_cursor"
         #Option     "hw_cursor"
         #Option     "NoAccel"
         #Option     "ShowCache"
         #Option     "ShadowFB"
         #Option     "UseFBDev"
         #Option     "Rotate"
	Identifier  "Card0"
# The following line is auto-generated by KNOPPIX mkxf86config
	Driver      "nv"
	VendorName  "All"
	BoardName   "All"
	BusID       "PCI:01:00:0"
EndSection

Section "Device"
	### Available Driver options are:-
# sw_cursor is needed for some ati and radeon cards
         #Option     "sw_cursor"
         #Option     "hw_cursor"
         #Option     "NoAccel"
         #Option     "ShowCache"
         #Option     "ShadowFB"
         #Option     "UseFBDev"
         #Option     "Rotate"
	Identifier  "Card1"
# The following line is auto-generated by KNOPPIX mkxf86config
	Driver      "mga"
	VendorName  "All"
	BoardName   "All"
	BusID       "PCI:00:13:0"
EndSection

Section "Screen"
	Identifier "Screen0"
	Device     "Card0"
	Monitor    "Monitor0"
	DefaultColorDepth 16
	SubSection "Display"
		Depth     1
		Modes "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     4
		Modes "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     8
		Modes "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     15
		Modes "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     16
		Modes "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     24
		Modes "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     32
		Modes "1024x768" "800x600" "640x480"
	EndSubSection
EndSection

Section "Screen"
	Identifier "Screen1"
	Device     "Card1"
	Monitor    "Monitor1"
	DefaultColorDepth 16
	SubSection "Display"
		Depth     1
		Modes "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     4
		Modes "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     8
		Modes "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     15
		Modes "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     16
		Modes "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     24
		Modes "1024x768" "800x600" "640x480"
	EndSubSection
	SubSection "Display"
		Depth     32
		Modes "1024x768" "800x600" "640x480"
	EndSubSection
EndSection

Section "DRI"
	Mode 0666
EndSection

#schnapp

Jetzt passiert folgendes: Der Rechner fährt auf Monitor 0 hoch und 
versucht dann, den X-Server zu starten. Screen 1 sagt "no signal" . In 
dem Moment, wenn auf Screen 0 der X-Server starten möchte, springt 
Screen 1 an und gibt und zeigt die Matrox an. Danach ist hängen im 
Schacht. Beide Screens sind dunkel, kein wie auch immer gearteter 
X-Server läuft, login auf einer anderen Textkonsole nicht möglich. Meine 
Vermutung ist, das ich vielleicht irgendeinen Bock bei der Bus-ID 
geschossen habe.
Ich weiß echt nicht mehr, wo ich den Fehler sonst suchen soll. 
Vielleicht erbarmt sich nochmal jemand.

Vielen Dank für eure Geduld.

Gruss

Juergen

-- 

Juergen Gruenebaum
Mail: juergen@raescom.de

Juergen Gruenebaum

Stichworte

Teilnehmer (2)